EMAX Reciprocating air compressor. Sits on top of its own air receiver. Driven by 7.5 HP motor, 220v 1 phase.. Maximum 175 psi and 26 scfm. Sits on 80 gallon reservoir. Refrigerated air, refrigerant is 134A. Refrigerated dryer is EMAX Model EDRCF1150030. Built 2020. Currently on filter press and pumping system. Part of an entire CBD extraction system - enter PK6020 to see all components.

Ingersoll Rand recip air compressor Model P1.5IU-A9, serial P20288T19051. Capacity 4.6 cfm at 135 psig. Voltage 115/1/60 2HP. With integral reservoir tank 20 gallons. Overall size 23" wide x 43" tall. Belt driven quiet operation 75 dBA. This part of gryphon CBD dryer system belt tensioner and NOT SOLD Separately. Part of an entire CBD extraction system - enter PK6020 to see all components.

Belt conveyor, rubber cleated 23.625" wide. . Includes hopper infeed. Drive motor is 1/2 HP 230/460 3/60 1725 rpm with Nord gaer unit. Built 2019. Part of an entire CBD extraction system - enter PK6020 to see all components.

Gryphon biomass gas fired recirculating air dryer. Model A.318. dryer section is 3 ft wide x 18 ft long. Used for drying hemp with inlet moisture of 50-80% and outlet moisture of 7% to 11% moisture running at 3,000 #/day inlet and approximately 1,000 #/ay dry mass outlet. Natural gas burner rated at 1.5 MMBTU with all gas train valves, firing controls and Honeywell fire eye safeties. Supplemental electric heaters in each of the three sections. Air flow is by blower rated at xxxx cfm with VFD drive AB PowerFlex 753. AirPro Fan Type HPSM254 3600 rpm serial 23894 40HP built on 2008. Six VFD drives in all Allen Bradley PowerFlex 525. Condenser coils. Includes infeed sifter and lid lift assembly for easy maintenance and operation. Includes fabricated feed belt 23.625" wide cleated belt. Full automation by Rockwell Allen Bradley and controls provided. Software plc controlled air volume, temperature and cycle time. Automated washing of chambers, air filter, and belt. CTS cooling tower is part of the package. No need for baghouses, scrubbers, or exhaust stacks. See brochure in link for more information. Unit was purchased new in 2019 - only has 1,289 hours operation. Last used for hemp drying. Very good condition. Includes spares: (4) condenser filters, 1 dryer belt, bed skirts & spacers. Part of an entire CBD extraction system - enter PK6020 to see all components.

Conveyor - take off from Gryphon dryer. Part of an entire CBD extraction system - enter PK6020 to see all components.

CTS cooling tower and recirculating pump. This is a counter flow induced draft FRP water cooling tower. Tower ihas1.5 HP fan and 1HP condenser. The nameplate is worn off but this is most likely a T-260 tower rated at 60 tons. Cooling capacity 900,000 BTU/hr, air volume 14,700 cfm. Tower size approx 78" dia x 74" tall. Water circulating pump is Bell & Gossett size e-1532 size 2BD, pump construction SSF impeller dia 8" serial number C286138-01G91 with a 5HP motor 1800 rpm. This is an end suction close coupled foot mounted pump. See link for pump specs and tower specs (most likely the right model number). Part of Gryphon biomass drying system asset 2042 - NOT sold separately. Part of an entire CBD extraction system - enter PK6020 to see all components.

Vincent dewatering screw press Model CP-6VT, serial 19456-1. Full vapor tight press capable of 350 lbs per hour on a dry basis (4 tons/day). Can do 98% on oleoresin recovery, and 75-80% ethanol recovery. Driven by 5HP motor 480 v 3/60 with VFD explosion proof. Food grade on all contact surfaces. Comes with stand. Screw is 6" diameter with 5 stages of compression. Bought in 2019 - used less than 1 year. Very good condition. Part of an entire CBD extraction system - enter PK6020 to see all components.

Tramco inclined drag conveyor. Size 14.5" wide x 25 ft long rising 13 ft. Model 10" x 6" Bulk Flo, serial BF-2070. Driven by 5 HP motor. Capacities from 1500 cu ft/hr to 3,750 cu ft/hr. Part of an entire CBD extraction system - enter PK6020 to see all components.

Stainless steel drums. Approx 11 drums with reinforcing bands, and 16 drums without reinforcing band. Quantity (27) - priced for the LOT. Part of an entire CBD extraction system - enter PK6020 to see all components.

Bizzybee falling film evaporator.Model BZB, MTA chiller, and pups. Used for recovering ethanol at up to 225L per hour (45-60 gallons per hour) continuous evaporation with 48 KW of heating at 480v and 13 tons of cooling. Serial no. BZB.1111.0000. Approved for both ethanol and heptane use. Includes vacuum pump and 3 liquid pumps. Physical size of rack is 3' x 3' and chiller & heater take up approx 9 sq ft more. Includes MTA chiller rated at 13 tons. Model TAEevo TECH 161. Refrigerant R410A. 30HP. Tru Temp heater rated at 48 KW. Vacuum pump is Agilent Model IDP-7. Was bought new in 2019 - was run for less than a year. See brochure in link. Very good condition. Part of an entire CBD extraction system - enter PK6020 to see all components.

Plate and frame filter press system including filter press, slurry tank for diatomaceous earth/filter aid addition, (2) stainless steel Yamada diaphragm pumps. Hydraulic clamping pressure 3500 psi. Last used for winterization filtering of crude hemp/CBD oil. Full model number FP630G32L-16/32-5/10AXX, serial FP01254. Filter Press by Watermark Model Pro X FP630. Plate dimensions 630mm x 630mm (24" x 24"), has 18 total plates for 72 sq ft surface area. Hydraulics air driven, 2" feed pipe and 1.5" discharge piping. Slurry tank is poly with cone bottom. See representative drawing in link. Bought new - used less than 1 year. Very good condition. Approx size filter 30.5" wide x 152" long x 52" tall. Precoat skid is 64" x 46" x 73" tall. Part of an entire CBD extraction system - enter PK6020 to see all components.

Horizontal stainless steel tank, on saddles. Size 67" dia x 94" long for capacity of 1,800 gallons.

Radwag moisture analyzer Model MA 50.R. Maximum capacity 50g, heating with IR emitter. Repeatability +/- 0.05% and can read moisture content down to 0.001%. Power supply 100-240 vac 50/60 Hz. Consumption 450W. Physical size 470x380x336 mm, weight 4.8kg

Biomass drying and ethanol solvent extractor system, last used for producing CBD Extract by drying hemp at 3,000 #/day infeed and approximately 1,000 #/day dry mass outlet. Was running hemp with infeed moisture of 50-80% and outlet moisture of 7% to 11% moisture. CBD extraction efficiency is very good. Unit was purchased new in 2019 - only has 1,289 hours operation. Very good condition. Main components include Gryphon gas fired dryer, ribbon blender, Vincent dewatering press, Watermark filter press system, Nutsche filter, BizzyBee distillation system, walk-in freezer, tanks. See Links for equipment list and process flow chart.For all components enter the key word PK-6020 in search box..

Hotsy cold water pressure washer Model 1755, serial 11065360-162900. Rated at 2500 psi 5.6 gpm. Nozzle size 07.0. Electric powered 460/3/60 .10HP. Size approx 31" x 21" x 16" high

Chuck Gurdin double ribbon blender mixer, stainless steel. Insulated. Also comes with load cells scale. Spped adjustable with VFD. Capacity 155 cu ft. Approx size 55" x 168" long x 90" tall. Drum dimensions 44" wide x 120" long x 53" high. Driven by 25HP motor 1755 rpm with Dodge gear reducer. Part of an entire CBD extraction system - enter PK6020 to see all components.

Seitz Enzinger Noll filter press.. Model EF60/65CB serial no. 963048 rated at 6 bar (90 psi). Removable filter plate, Surface area 0.29 sq m, 100 liter.Construction ss316 stainless steel. Chamber 24" dia rated at 6 bar (87 psi) jacketed for 6.5 bar (94 psi) with manual screw lift. Built 1989. Note: This filter had a chiller no longer available. Part of an entire CBD extraction system - enter PK6020 to see all components.

Square stainless steel tank,reinforced sides. Size is 111" x 111" x 160" high - on legs for OAH 220". Atmospheric tank. Capacity approx 8500 gallons. Material ss304. Used for pure ethanol storage food grade. Part of an entire CBD extraction system - enter PK6020 to see all components.

Vertical stainless steel tank, insulated. Size 30.5" dia x 45" tall on legs for 76" OAH. Capacity 145 gallons.

Stainless steel ss304 vertical tank. Size 52.5" dia x 70.5" tall. Flat top, slight cone bottom. Capacity 600 gallons. Has short legs 6".

Stainless steel vertical tank - size 50" dia x 84" tall on legs for 117" OAH. Capavcity 580 gallons. Flat top, Cone bottom approx 45 degrees. On legs.

SRC walk in freezer Series IV, size 20' x 16' x 8' tall. Doorway width 50" wide x 78" tall. Energy efficient food grade freezer. Includes two double fan recirculating refrigeration and air handlers - refrigeration unit placed outside by Heatcraft Refrigeration Products Model LCE694BEB. These are Larkin low profile units, electric defrost type rated at 9400 BTUH each. Voltage 220/1/60. Bought in 2019 new, used for less than a year. In very good condition. Part of an entire CBD extraction system - enter PK6020 to see all components.