Unused Crown Iron Works approximately 5013 sqft (466 sqmt) 1st stage evaporator. T304 stainless steel tubes has (1064) 3/4 inch (19.05 mm) diameter x 24 feet (7315 mm) long 304 stainless steel tubes rated 15 psi/full vac (1.03 bar/full vac) design pressure. Has 58 inch (1473 mm) diameter x 24 feet (7315 mm) long shell rated +/-1 psi (-0.06/0.06 bar) design pressure. New 2004.

Mason Mfg. Evaporative Condenser 54 inch I.D. x 30 ft Tube length x 36'-2" OAL. Used, built 2004. Approx surface area 11,702 sq ft. Has 1,494 ss tubed at 1" OD. (2) Pass T.S. 190 proof condenser. Vapor Inlet 36". Water tube inlet/outlet 20" each one. MAWP shell 15 psig/full vacuum at 300F, tubes 75 psig at 300F. Material cs shell, 304ss tubes. Empty weight 38,000 pounds. These are As Is Where Is - not yet tested. Qty 3, priced separately.

Shell & Tube Condenser, Mason Mfg. Size 8" dia x 16 ft long x 17-'3" OAL. Material shell and tubes ss304L. Has 40 tubes 3/4" OD x 16 ft long for surface area of 125 sq ft. On saddles. Vapor inlet/outlet 3", liquid outlet 2". Water inlet/outlet 3". S/N 02-3883, Built 2002, ASME Nat'l Bd # 825 MAWP shell 55 psig/ f.v at 300F, tubes 100 psig at 300F. Empty weight 1000 pounds

Mason Mfg. Evaporative Condenser - 60 inch I.D. x 30 ft. tube length x 35'x2" OAL . New tubes - All tubes replaced (that measured over 10% loss). The internal area in the head where the water reverses for a second pass has been epoxy coated to cut down on any potential wear. Built 2005. Has 1,866 tubes 1" OD x 30 ft long for 14,655 sq ft surface are. Shell cs/tubes ss304. MAWP shell 15 psia/full vacuum at 250F. Tubes 75 psig @ 250F. Vapor inlet 40", Water inlet/outlet 24". (2) Pass T.S. 190 proof condenser. Empty weight 45,000 pounds

Unused Crown Iron Works 374 sqft (35 sqmt) horizontal condenser. Has (119) 3/4 inch (19.05 mm) diameter x 16 feet (4877 mm) long t304l stainless steel tubes rated -15/75 psi (-1.03/5.17 bar) design pressure at 250 deg.f (121 deg.c). Has 14 inch (356 mm) diameter x 16 ft (4877 mm) long carbon steel shell rated -15/165 psi (-1.03/11.37 bar) design pressure at 300 deg.f (149 deg.c). New 2004.

Condenser - 4 pass. Mason Mfg. S/N 02-3882 #H-1514. 424 sq ft

Shell & Tube Heat Exchanger - Condenser, Paget Equipment, S/N 06-143-A, Model C105. Built 2006. ASME Nat'l Bd # 20601 MAWP shell 75 psi at 200F, tubes 15 psig at 200F. Dia 30" OD x 346" OAL. Has 420 tubes 1" OD x 25 ft long for heat transfer area of 774sf. Material Shell/tubes ss304. There are two of these - priced separately. See LINKS for drawing

Unused Crown Iron Works desolvent toaster condenser. 5088 sqft (473 sqmt), has (1080) 3/4 inch (19.05 mm) diameter x 24 ft (7315 mm) long t304 stainless steel tubes rated 45 psi (3.1 bar) design pressure. Carbon steel shell 40 inch (1016 mm) diameter x 24 ft (7315 mm) long rated +/-1 psi (-0.06/0.06 bar) design pressure. New 2004.

Shell & tube heat exchanger designed for use as Evaporator Condenser. Built in 2007 by Paul Mueller Company. Size 72" OD x 391" (32.6 ft) OAL. TEMA type NEM. Has 1,785 ss 304L yubes 1.25" OD. MAWP Shell side: 150 psi @ 200 degrees F. Tube side: 50 psi @ 300 degrees F. Has 1,785 tubes at 1.25" OD x 216" long for approx 10,514 sf surface area. Material: shell cs SA-516 Gr 70, tubes ss304L. S/N 366273-13. Empty weight: 50,332 pounds. Built 2007 - never used. Nozzles: See Drawing link. 18 inch cooling water in/out. Tubeside non-condensables 4" inlet, 6" outlet. Tubeside condensables 3" inlet, 6 inch outlet. Also 54" tubeside inlet with 304ss cladding. This is new, never used in original packing crates.

Evaporative condenser: Evaporator capacity 37.4 MMBTUH, Material 304L SS shell & tube. Mfg by Apache ser num 11032-1, ASME NB# 1581, MAWP shell & tube 25 psi at 200F. Size 5'-6" dia x 50' s/s with an 8 ft cs skirt (OAH approx 60' - tube length 40 ft). See link for drawing and data. Used as Thermal Kinetics 1st and 2nd Stage/First Effect Evaporator

Evaporative condenser: Evaporator by Thermal Kinetics. Size 4.5' dia x 50' s/s on 8' cs skirt. OAH approx 60'. Capacity 45.1 MMBTUH, Material ss304L. Design: Tubes FV/25psig, 150F; Shell: FV/75psig, 200F. Used as Thermal Kinetics 3rd and 4th Stage/Second Effect Evaporator

Unused Crown Iron Works 9498 sqft (882 sqmt) 304 ss horizontal evaporator condenser. Has (2016) 3/4 inch (19.05 mm) diameter x 24 ft (7315 mm) long 304 stainless steel tubes rated 55 psi (3.70 bar) design pressure at 100 deg.f (38 deg.c). Has 56 inch (1422 mm) diameter x 24 ft (7315 mm) long shell rated +/-15 psi (-1.03/1.03 bar) design pressure at 212 deg.f (100 deg.c). 4 pass tube side, 2 pass shell side. New 2004. Vapor inlet 36:. Shell 56" OD x 24 ft.Overall size 6 ft top to bottom x 27ft-2" long, empty weight approx 32,970 pounds

Used 84 sq ft Doyle and Roth heat exchanger U tube design, with (54).75" diameter x 8' long 316 stainless steel tubes rated 150 psi at 400 f, carbon steel bonnet, carbon steel shell rated 150 psi at 400 f, Serial# J4195, National Board #12214, built 1984.

1819 sq ft Heat Exchanger, Mfg by Thermotran. Tube & shell material: Carbon steel. Shell Pressure 150 psig, Shell Temperature 150 degrees F. Tube Pressure 1040 psig, Tube Temperature 355 degrees F. Shell Pass: 2, Tube Pass: 2, Tubes 340. Length 30 feet. NB#139, S/N H-1441, Wt: 15,900 lbs.

Shell & Tube Exchanger, 10 ft Long, 6" pipe

Plate Heat Exchanger. Sondex, Inc. S/N 9107. Model # S201S38. ASME Nat'l Bd# 541, MAWP 150 psi at 200F, Design pressure 150 psi. Corrugated herringbone pattern plates - designed for one pass solutions. Built 2007 - removed and ready to load

Approx 49 plates for Alfa Laval plate heat exchanger X-400 - priced for the lot

Alfa Laval Heat exchanger Plates - Wide gap for MA30-SFG heat exchanger, regasketed. Approximately 165, priced separately.

Shell & tube heat exchanger, designed for use as a Reflux Vent Condenser. Built in 2007 by Paul Mueller Company. TEMA type BEM. Shell cs, tubes ss304L. MAWP Shell Side: 150 psi @ 200 degrees F. Tube Side: 75 psi @ 200 degrees F. Size 16" OD x 108" OAL. Has 212 tubes at 0.75" od x 72" long for approx 249 sf surface area. Empty Weight 1664 pounds. S/N 366273-7. See drawing in Links. This is new, never used.

Shell & tube heat exchanger designed for use as a Mix Tank Vent Condenser. Built in 2007 by Paul Mueller Company. Size 16" OD x 143" OAL. Shell cs, tubes 304L. MAWP Shell Side: 150 psi @ 300 degrees F. Tube Side: 75 psi @ 300 degrees F. Has 212 tubes at 0.75" OD x 120" long for approx 416 sf surfaced area S/N 366273-1. Empty Weight 2167 pounds. This is new, never used.

Fin tube heat exchanger, hairpin design, 1 turn u-tube mfg by Koch Heat Transfer Company. Has 223 sq ft heat exchange area. Rated at 1.81 MMBTU/hr, Syn Gas 300/110, Water 90/110F. 0.75/0.065, 2700 #. ASME rated at 215/FV at 350F. Stainless steel 304. Physical size 8" dia sch40. Built in 2009 - ran only 42 days - like new. Used as 1st Stage Booster Intercooler.

Fin tube heat exchanger, hairpin design, 1 turn u-tube built by Koch Heat Transfer Company in 2009 - 298 sq ft heat exchange area. Rated at 1.811.69 MMBTU/hr, ASME MAWP tubes 400 psig/FV at 350F and shell 305 psig at 250F, Nat'l Bd# 19195, s/n 12110-09-2-01. Water 90/110F, Syn Gas 300/110F. 0.75/0.065, 2950 #. Tubes 304SS, shell cs, size 8 in dia, schedule 40. Used as 2nd Stage Booster Intercooler

Fin tube heat exchanger Koch Heat Exchanger - hairpin design, 1 turn u-tube 162 sq ft surface area. Designed for 1.04 MMBTU/hr, Syn Gas 300/110F, Water 90/110F. 0.75/0.083, 2790 #. ASME MAWP shell 800 psig/FV at 350F, tubes 615 psig at 250F, Nat'l Bd# 19197, s/n 12110-09-4-01. Material 8 inch carbon steel. Built by Koch Heat Transfer Company in 2009 - used only 42 days - like new. Used as 4th Stage Booster Spillback Cooler.

Tranter Superchanger plate heat exchanger - FRAME ONLY - plate pack gone. Original design: Model GFP-167-M-8-HP-55 , capacity 4.47 MMBTUH Material 304 SS Design 50 psig / 220 deg F. See link for drawing and U-1. Last used as Beer Preheater No. 1

Tranter Superchanger plate heat exchanger - FRAME ONLY - Plate pack missing. (original design was capacity 4.47 MMBTUH Material 304 SS Design 50 psig / 220 ?F. See link for drawing and U-1. Last used as Beer Preheater No. 2 )