18 inch Auger 140 inches long

Two 36 inch wide x 40 ft long coal and lime transfer belts to main belt to combustor There are two systems here - sold as a set. Each has large dump hopper, independently driven conveyor. Variable feed rate from 2 to 50 TPH. Each belt driven by 10HP motor.

Trough belt conveying system and structure. Inclined trough belt conveyor mfg by Martin. Martin model S Class air supported belt. Size 24" wide x 450 ft long. Inclined conveyor has equivalent of 73 ft vertical lift - 150 fpm speed. Designed for 50 tons/hr of coal at 35 lb/cf and of lime at 87.5 lb/cf density. Has four blowers; each driven by 40 HP motor. Includes structural steel. Used to transport coal and line from hoop house to combustor. The entire system is available, however, we will sell equipment individually. See Simplified Flow Chart in Links for a pictorial of each piece in this system. For a list of all components, enter PK9140 in the search box

Nordic Cake Drag Chain Conveyor. Galvanized. Part of Crush package. For a list of all components, enter "pkcrush" in the keyword search terms box.

Tramco chain drag conveyor, Model G sn G-3647. Size 15" x 20" x 32 ft OAL. Carbon steel. 124 2-piece flights 4" x 14-1/16 x 3/4" thk. Designed for 102.2 fpm capacity 1,345 cu ft/hr of coal PRB at density 45 lb/cu ft. Design capacity is about 30 tons/hr. Has 3 openings for hopper feeding - each opening has a manual handwheel gate closer. Built 2005. est wt 7,439

Tramco chain drag conveyor, G-Model, sn G-3646. Size 30" x 20" x OAL 33'3". Designed for 101.4 fpm, 12,000 cfh of coal sized. Has (71) flights 4" x 28-1/8" x 3/4" thk. Driven by 20 HP motor 460/3/60. Est wt 19,610 pounds

Conveyor Auger, Carbon steel. 18 inch auger x 15 ft long. 19 inch inside diameter.

Conveyor Drive end section for chain drag conveyor. Includes bearings and motor sheave.

Bottle conveyor, stainless steel frame and ss cover. 4" Delrin belting on teflon guides. Adjustable ss side rails. Driven by 3/4 HP Leeson motor with locally mounted Reliance VFD control - Length approx 10 ft.

Filler feed conveyor. Stainless steel frame and ss cover. 4" Delrin belting on teflon guides. Adjustable ss side rails. Driven by fractional HP motor with locally mounted VFD control - Length approx 20

Capper feed conveyor. Stainless steel frame. 4" Delrin belting on teflon guides. Adjustable ss side rails. Driven by fractional HP motor with locally mounted VFD control - Length approx 6 feet

Check weigher feed conveyor. Stainless steel frame, 4" Delrin belting on teflon guides. Adjustable ss side rails. Driven by fractional HP motor with locally mounted VFD control - Has a 90 degree turn, approx 1 ft and 3 feet

Sleever feed conveyor. Stainless steel frame, 4" Delrin belting on teflon guides. Adjustable ss side rails. Driven by fractional HP motor with locally mounted VFD control, length approx 40 feet

Diverter valve - 2-way. Mfg by Dust Control and Loading Systems (DCL) Model CBSDV30-18 (Curved blade symmetric diverter valve). Inlet 18" square, height 34", discharge flanges (2) 18" square each at 30 degrees off vertical. Material carbon steel. Last used as coal feed diverter to feed metering bins.

Drag conveyor 21'-10"x 12 in wide. Essmueller flat bottom drag Model 1210FB81. Material cs. Designed for 3100 cfh ground corn at 45 PCF. Has 106 flights. Driven by 2 HP motor 58 rpm. Set at 9 degree incline. See links for drawing. Last used as feed to hammermill elevator leg inlet.

Essmueller Conveyor Model 1213FB88 horizontal flat bottom drag conveyor. 23'-8" long OAL 25'-10"). Designed for 1920 CFH of DDG at 45 #/cf running at a speed of 100 fpm. Has 58 flights and chain driven by a 2 HP motor. Material cs. See link for drawing. Used as conveyor from dryers to DDGS transfer conveyor.

Drag Conveyor carbon steel, size approx 2 ft x 2 ft x 28 ft long. Has been removed - ready for loading

Drag conveyor stainless steel mfg by Essmueller. Model RB16" x 54 ft long. (OAL 56'-5"). Designed for capacity 55,178 PPH, 2000 cfh of wet DDG at 55 PCF, 100 fpm. Material 304 SS. Has 129 UHMW flights, ss chain. Driven by 5 HP motor. Used as Wet Cake Transfer Conveyor No. 1 at dryer system. See drawing in Links.

Drag conveyor horizontal 75'-4" long x 29" wide, carbon steel. Rated for 240 tons/hr of DDGS at 35 #/cu ft. about 13,700 CFH). Has 112 flights, material UMHW polyethylene, chain driven at 146 ft/min by 20 HP motor 460/3/60. See conveyor drawing in LINKS. Includes steel structure bridge, galvanized. Used as feed conveyor for the DDGS for loadout to Dynatek/SLY system. Part of the DDGS load out system but will be sold separately. Fort a list of all comonents of the DDGS load out system, enter PK8420 in the search box

Drag Conveyor, stainless steel - transition from horizontal to vertical. Horizontal length approx 44 ft x vertical lift approx 38 ft (OAH 40 ft & OAL 80'-7"). Width approx 10". Poly drag flights. Designed for 2,000 CFH of Wet DDGs (WDG) at 55 PCF. Speed is 67 ft.min. Material ss304 stainless. Capacity 110,000 PPH. Driven by 15 HP motor 1800 rpm. See conveyor drawing in links. Used as drag under all 3 centrifuges to Dryer area.

Essmueller flat bottom horizontal drag conveyor 35'-6" long (OAL 38'7") Designed for 15,000 CFH DDGS at 32 PCF at speed of 73 fpm. Has 77 flights, chain driven by 15 HP motor 460/3/60. Material cs. See link for drawing. Used as drag to SLY DDGS loadout system

Essmueller drag conveyor 49'-10" long (OAL 53') designed for 15,000 CFH DDGS at 32 PCF. Horizontal drag running at 73 fpm. Has 105 flights chain driven. Material cs. Driven by 15 HP motor 460/3/560. This conveyor is in DDGS storage pit - no photos available - feeds elevator CE-8411. See link for drawing. Last used for DDGS Reclaim Drag Conveyor

Essmueller incline 7 degrees drag conveyor, flat bottom. Model 1213FB81 - 55'-5" conveyor (57'-7" overall length). Designed for 2100 CFH DDGS at 32 PCF at a speed of 65 fpm. Has 132 flights chain driven, by a 3 HP motor 460/3/60. See link for drawing. Last used as the DDGS Transfer Conveyor from Dryers to CE-8402. Material CS

Drag conveyor by Essmueller, Flat bottom En-Masse drag - Length 64'-11" horizontal. Designed for DDGS at 35 PCF, capacity 2100 CFH 50 fpm. Driven by 3 HP motor 1750 rpm 460/3/60. Material CS, See link for drawing. Used as DDGS Distribution Drag Conveyor No. 1

Essmueller Drag conveyor model 1818HF124, ss 304L. Capacity 49,149 PPH. Driven by 15 HP motor. Used as Elevating Transfer Drag Conveyor - Dryer No. 1. Part of Dryer #1 ancillary package - enter PK5410 for a list of all components.