Alfa Laval B214A centrifuge. The complete unit will be reconditioned, balanced, new seals/bearings, painted. Photo shows machine prior to reconditioning - allow 4 to 6 weeks delivery. Reconditioning includes, complete disassembly of machine, sandblast and paint all carbon steel parts, remove gear pump, install end plate, Rebuild using all new parts, Bearings, seals, and O-rings (Viton), All Vibration Isolators units will be tested and come with manuals, some tools and one set of gravity discs. High speed balance will also be performed. 40hp motor will be rebuilt or new depending upon timing. Welcome to inspect the machine as tests are run to verify balance. Centrifuge can also be purchased " as is, where is " if desired.

Alfa Laval B214C centrifuge. The complete unit will be reconditioned, balanced, new seals/bearings, painted. Photo shows machine prior to reconditioning - allow 4 to 6 weeks delivery. We can quote an "As Is" price if desired.

DeLaval B214C solid bowl disc centrifuge. Serial number 3532804. Capacity approximately 36,000 to 40,000 #/hr. Motor is 40HP. Cleaned and painted, epoxy internal coating but not reconditioned. Bowl removed and crated for shipping. Very good condition

Used REBUILT GEA Westfalia model SA 45-03-177 self-cleaning disc centrifuge. Includes: Frame, Bowl, Motor, Cover, Valves, Foundation frame, Tools, Controls, Manual and some spare parts. Separator Bowl design: Open gravity light phase, paring device Heavy phase. 4920 RPM. Sanitary design. 3-way separator with Gravity discharge (see spout on hood). Flange type vertical mounted motor. SN 1697 834. Mfg 1989 - Rebuilt - allow 8-10 weeks. Concentrator design - capable of handling 10-40% water. Max flow rate 110 gpm on water, no solids. Actual flow rate depends on feed and solids.

Alfa Laval centrifuge Model MAB 206-S-24-60-HZ. Serial No. 2965454 Throughput capacity approx 10.6 m3/h. Separation takes place in a solids-retaining bowl that can be arranged for either clarification or purification. Solids retained in bowl and removed by manually cleaning. Was in biodiesel service. Still installed. Voltage: 3-Phase 575v. There are (2) MAB centrifuges here. If both are bought, we can ship on the skid they are mounted on. Price is for EACH MAB centrifuge which includes removal and loading on your truck. Controls not included. Local Start/Stop Control Only. We can provide this panel at additional charge.

Alfa Laval centrifuge Model MAB 206S-24-60/4049-8. Serial No. 4032493. Throughput capacity approx 10.6 m3/h. Separation takes place in a solids-retaining bowl that can be arranged for either clarification or purification. Solids retained in bowl and removed by manually cleaning. Was in biodiesel service. Still installed. Voltage: 3-Phase 575. There are (2) MAB centrifuges here. If both are bought, we can ship on the skid they are mounted on. Price is for EACH MAB centrifuge which includes removal and loading on your truck. Controls not included. Local Start/Stop Control Only. We can provide this panel at additional charge.

One (1) Reconditioned Westfalia Model OSB-35-02 Self-Cleaning centrifuge to include: Max. Hydraulic Capacity: 90 GPM, Max. Process Capacity: Varies depending on process conditions, Viton o-rings used in product contact areas, Direct-drive design, Variable shoot design (partial or full shot), Stainless steel rotating assembly, Powder-coated grey iron frame and silumin cover, 20 HP Class 1., Div. 1 explosion-proof motor - 460/480 Volt, 3 phase, 60 cycle, Heavy Phase (water) discharged by gravity, Light Phase (oil) discharged under pressure by means of a paring disk (centripetal pump), One (1) set of regulating discs, One (1) set of necessary special tools, One (1) set of spare bowl o-rings, One (1) copy of the Operation / Spare parts Manual, Feed pump not included. Customer required to supply their own feed pump.

Remanufactured Westfalia model OSB 35-02-576 single pump on light phase, heavy phase by gravity oil purifer. No controls. Capacity nominal 23,000 liters/hr (100 gpm). This machine is completely rebuilt. This includes replacement of bearings, seals and remanufacture of any substandard parts. The exterior cosmetics are restored to the best possible condition. The machine will be assembled, balanced, and run for several hours prior to shipping.. Warranty 6 months. Ready to ship - one week. Includes:20 HP, 480 Volt, 3 Phase, 60 Cycle Explosion Proof Motor 6500 RPM Bowl Speed, 11,000 G Force Paring Device on Light Phase Gravity Discharge on Heavy Phase Direct Drive Powder Coated Frame 20 Litre Bowl Volume 11 Litre Sludge Space 40 Degree Bowl with 0.5 MM Caulk Space Stainless Bowl SS Bowl Liner, with set of Erosion Clips Water Harness Special Set of Tools Operation / Parts Manual

Alfa Laval PX60 centrifuge. Model PX60 VGD 14 CGH 60. Capacity approx 14,000 lb.hr - was running on veg oil for both primary separation and for degumming. 2 phase. Ser num 4077200, built 1994. Max bowl speed 6235 rpm. Max feed density 1040 kg/m3. Approx 30 HP motor with soft start. Includes controls, tools, water harness. Idled in 2020. See complete nameplate data in Link. Removed, ready to load

Alfa Laval PX65 centrifuge, sn 4201906-2011. Capacity approx. 22,000 lb/hr. Max speed 7500 rpm. Max density feed 1100 kg/m3. Includes tools, water harness, controls and VFD. Driven by 40 HP motor. Used for primary separation and degumming - 2 phase operation. Built 2011, This unit has now been removed and is ready for loading. See data plate info and actual operation video in Link.

Westfalia RSA 60-01-076 vegetable oil separator. Max bowl speed 6450 RPM, Rated @ 13000 LPH, both liquid phases discharged under pressure, 15KW motor. Explosion Proof Motor. No tools or Controls. Was recently taken apart and thoroughly cleaned/inspected.

Reconditioned Westfalia RSA 80 disc centrifuge 3-phase RSA80-01-076 16,000 liters/hr (70 gpm). Built 1980, completely reconditioned in 2022 with NEW motor and NEW controls RPM 4500, bowl dia 30.5" so RCF (g force) = 8,785 New 480v motor - direct drive Includes bowl insertion tools, water harness, Control panel with VFD and programming NEMA 4 Carbon steel skid for mounting machine, water harness, control panel. (Control panel will be bolted on separate wood skid for shipping - can be bolted on centrifuge steel skid or mounted remotely upon installation) All tested, operated, balanced in shop Bought for a project but never used, already reconditioned, ready to load. We will load your tuck. Centrifuge bowl will be removed and crated separately for shipment.

Westfalia RSE 100-01-776 centrifuge. As is. S/N 1715325.

Westfalia RSE 200-01-776 Separator centrifuge - NEW - has never been put into service. Ready to ship. 2004 Model. Serial num 1724279. Includes all tools and a) 50 HP, 480 Volt, 3 Phase, 60 Cycle Drive Motor b) All Stainless Steel Wetted Contact Parts c) Both Liquid Phases Discharged under Pressure d) Bowl Volume 70 Litres, Solids Capacity 25 Litres e) Bowl Specs 0.5 mm Disc Caulk Spacing, Inner Rising Channels f) Feed and Discharge Connections g) Discharge Port Liners and Bowl Liner h) Max Bowl Speed 4800 RPM with 9000 G's . Diameter 687mm. i) Inlet / Outlet Gauges and Back Pressure Regulator j) Gear Drive Direct Coupled, VFD Driven Motor k) Vibration Isolators and Foundation Frame l) Water Controls are integral part of the machine m) Operation / Spare Parts Manual

Westfalia SAMN 15037 centrifuge. This is a 3 phase separator. Year 1975 with a BSB 100 rotary brush strainer This machine was overhauled by Westfalia 2009 and was removed in 2011, it was in a winery and used to work around 4 weeks a year, to filter the new wine, with yearly inspections by Westfalia technical service after. Drum and mechanical parts are in very good condition (inspected by a technician during dismantling). 380V/50Hz/3 phase.